Is it a bad idea to drill a hole through this door frame to pass wires?
I want to pass my ethernet, speaker and sub wires into my newly built media/bar cabinet, but I hate having to pass them under the door, so I'd like to drill a hole as shown by the green circle in the image.
Bad idea?
doors closet
edited Dec 29 '18 at 23:58
Tim Medora
1034
asked Dec 29 '18 at 14:08
jwilcox09jwilcox09
1084
add a comment |
I want to pass my ethernet, speaker and sub wires into my newly built media/bar cabinet, but I hate having to pass them under the door, so I'd like to drill a hole as shown by the green circle in the image.
Bad idea?
doors closet
edited Dec 29 '18 at 23:58
Tim Medora
1034
asked Dec 29 '18 at 14:08
jwilcox09jwilcox09
1084
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
Dec 29 '18 at 15:28
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
Dec 29 '18 at 18:23
1
You're not going to run mains power through this, are you?
– Harper
Dec 29 '18 at 18:29
add a comment |
I want to pass my ethernet, speaker and sub wires into my newly built media/bar cabinet, but I hate having to pass them under the door, so I'd like to drill a hole as shown by the green circle in the image.
Bad idea?
doors closet
edited Dec 29 '18 at 23:58
Tim Medora
1034
asked Dec 29 '18 at 14:08
jwilcox09jwilcox09
1084
I want to pass my ethernet, speaker and sub wires into my newly built media/bar cabinet, but I hate having to pass them under the door, so I'd like to drill a hole as shown by the green circle in the image.
Bad idea?
doors closet
doors closet
edited Dec 29 '18 at 23:58
Tim Medora
1034
asked Dec 29 '18 at 14:08
jwilcox09jwilcox09
1084
edited Dec 29 '18 at 23:58
Tim Medora
1034
asked Dec 29 '18 at 14:08
jwilcox09jwilcox09
1084
edited Dec 29 '18 at 23:58
Tim Medora
1034
edited Dec 29 '18 at 23:58
Tim Medora
1034
edited Dec 29 '18 at 23:58
Tim Medora
1034
1034
asked Dec 29 '18 at 14:08
jwilcox09jwilcox09
1084
asked Dec 29 '18 at 14:08
jwilcox09jwilcox09
1084
asked Dec 29 '18 at 14:08
jwilcox09jwilcox09
1084
1084
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
Dec 29 '18 at 15:28
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
Dec 29 '18 at 18:23
1
You're not going to run mains power through this, are you?
– Harper
Dec 29 '18 at 18:29
add a comment |
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
Dec 29 '18 at 15:28
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
Dec 29 '18 at 18:23
1
You're not going to run mains power through this, are you?
– Harper
Dec 29 '18 at 18:29
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
Dec 29 '18 at 15:28
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
Dec 29 '18 at 15:28
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
Dec 29 '18 at 18:23
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
Dec 29 '18 at 18:23
1
1
You're not going to run mains power through this, are you?
– Harper
Dec 29 '18 at 18:29
You're not going to run mains power through this, are you?
– Harper
Dec 29 '18 at 18:29
add a comment |
3 Answers
3
active
oldest
votes
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered Dec 29 '18 at 15:49
BillWeckelBillWeckel
1,134110
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
Dec 29 '18 at 17:25
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
Dec 29 '18 at 20:16
1
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
Dec 29 '18 at 20:23
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
Dec 29 '18 at 20:45
Would using a spade bit do the trick as well?
– jwilcox09
Dec 30 '18 at 17:08
|
show 1 more comment
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered Dec 29 '18 at 14:58
Rohit SaxenaRohit Saxena
1192
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
Dec 29 '18 at 15:02
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
Dec 29 '18 at 15:06
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
Dec 29 '18 at 15:16
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
Dec 29 '18 at 17:11
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
Dec 29 '18 at 21:30
|
show 3 more comments
Probably too late but I would actually go through the wall between the molding and the corner. Measure things on the side from the picture, transpose the hole location into the other room and drill from the other room. 3/4" auger or installer bit should fit fine. That's just me.
Drilling the frame will end up being like 5" of solid wood counting the doubled stud and the molding, drilling into that space will be just wall material/hollow cavity/wall material. It will also be less likely to cause issues in the future. Need larger hole? Elongate with a jab saw, and use those plastic cable hiders to cover the hole.
answered Dec 31 '18 at 22:43
Edward HaynesEdward Haynes
111
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f153654%2fis-it-a-bad-idea-to-drill-a-hole-through-this-door-frame-to-pass-wires%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
3 Answers
3
active
oldest
votes
3 Answers
3
active
oldest
votes
active
oldest
votes
active
oldest
votes
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered Dec 29 '18 at 15:49
BillWeckelBillWeckel
1,134110
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
Dec 29 '18 at 17:25
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
Dec 29 '18 at 20:16
1
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
Dec 29 '18 at 20:23
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
Dec 29 '18 at 20:45
Would using a spade bit do the trick as well?
– jwilcox09
Dec 30 '18 at 17:08
|
show 1 more comment
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered Dec 29 '18 at 15:49
BillWeckelBillWeckel
1,134110
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
Dec 29 '18 at 17:25
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
Dec 29 '18 at 20:16
1
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
Dec 29 '18 at 20:23
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
Dec 29 '18 at 20:45
Would using a spade bit do the trick as well?
– jwilcox09
Dec 30 '18 at 17:08
|
show 1 more comment
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered Dec 29 '18 at 15:49
BillWeckelBillWeckel
1,134110
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered Dec 29 '18 at 15:49
BillWeckelBillWeckel
1,134110
answered Dec 29 '18 at 15:49
BillWeckelBillWeckel
1,134110
answered Dec 29 '18 at 15:49
BillWeckelBillWeckel
1,134110
answered Dec 29 '18 at 15:49
BillWeckelBillWeckel
1,134110
1,134110
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
Dec 29 '18 at 17:25
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
Dec 29 '18 at 20:16
1
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
Dec 29 '18 at 20:23
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
Dec 29 '18 at 20:45
Would using a spade bit do the trick as well?
– jwilcox09
Dec 30 '18 at 17:08
|
show 1 more comment
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
Dec 29 '18 at 17:25
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
Dec 29 '18 at 20:16
1
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
Dec 29 '18 at 20:23
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
Dec 29 '18 at 20:45
Would using a spade bit do the trick as well?
– jwilcox09
Dec 30 '18 at 17:08
4
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
Dec 29 '18 at 17:25
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
Dec 29 '18 at 17:25
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
Dec 29 '18 at 20:16
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
Dec 29 '18 at 20:16
1
1
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
Dec 29 '18 at 20:23
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
Dec 29 '18 at 20:23
1
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
Dec 29 '18 at 20:45
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
Dec 29 '18 at 20:45
Would using a spade bit do the trick as well?
– jwilcox09
Dec 30 '18 at 17:08
Would using a spade bit do the trick as well?
– jwilcox09
Dec 30 '18 at 17:08
|
show 1 more comment
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered Dec 29 '18 at 14:58
Rohit SaxenaRohit Saxena
1192
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
Dec 29 '18 at 15:02
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
Dec 29 '18 at 15:06
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
Dec 29 '18 at 15:16
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
Dec 29 '18 at 17:11
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
Dec 29 '18 at 21:30
|
show 3 more comments
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered Dec 29 '18 at 14:58
Rohit SaxenaRohit Saxena
1192
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
Dec 29 '18 at 15:02
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
Dec 29 '18 at 15:06
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
Dec 29 '18 at 15:16
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
Dec 29 '18 at 17:11
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
Dec 29 '18 at 21:30
|
show 3 more comments
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered Dec 29 '18 at 14:58
Rohit SaxenaRohit Saxena
1192
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered Dec 29 '18 at 14:58
Rohit SaxenaRohit Saxena
1192
answered Dec 29 '18 at 14:58
Rohit SaxenaRohit Saxena
1192
answered Dec 29 '18 at 14:58
Rohit SaxenaRohit Saxena
1192
answered Dec 29 '18 at 14:58
Rohit SaxenaRohit Saxena
1192
1192
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
Dec 29 '18 at 15:02
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
Dec 29 '18 at 15:06
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
Dec 29 '18 at 15:16
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
Dec 29 '18 at 17:11
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
Dec 29 '18 at 21:30
|
show 3 more comments
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
Dec 29 '18 at 15:02
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
Dec 29 '18 at 15:06
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
Dec 29 '18 at 15:16
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
Dec 29 '18 at 17:11
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
Dec 29 '18 at 21:30
1
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
Dec 29 '18 at 15:02
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
Dec 29 '18 at 15:02
1
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
Dec 29 '18 at 15:06
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
Dec 29 '18 at 15:06
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
Dec 29 '18 at 15:16
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
Dec 29 '18 at 15:16
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
Dec 29 '18 at 17:11
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
Dec 29 '18 at 17:11
1
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
Dec 29 '18 at 21:30
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
Dec 29 '18 at 21:30
|
show 3 more comments
Probably too late but I would actually go through the wall between the molding and the corner. Measure things on the side from the picture, transpose the hole location into the other room and drill from the other room. 3/4" auger or installer bit should fit fine. That's just me.
Drilling the frame will end up being like 5" of solid wood counting the doubled stud and the molding, drilling into that space will be just wall material/hollow cavity/wall material. It will also be less likely to cause issues in the future. Need larger hole? Elongate with a jab saw, and use those plastic cable hiders to cover the hole.
answered Dec 31 '18 at 22:43
Edward HaynesEdward Haynes
111
add a comment |
Probably too late but I would actually go through the wall between the molding and the corner. Measure things on the side from the picture, transpose the hole location into the other room and drill from the other room. 3/4" auger or installer bit should fit fine. That's just me.
Drilling the frame will end up being like 5" of solid wood counting the doubled stud and the molding, drilling into that space will be just wall material/hollow cavity/wall material. It will also be less likely to cause issues in the future. Need larger hole? Elongate with a jab saw, and use those plastic cable hiders to cover the hole.
answered Dec 31 '18 at 22:43
Edward HaynesEdward Haynes
111
add a comment |
Probably too late but I would actually go through the wall between the molding and the corner. Measure things on the side from the picture, transpose the hole location into the other room and drill from the other room. 3/4" auger or installer bit should fit fine. That's just me.
Drilling the frame will end up being like 5" of solid wood counting the doubled stud and the molding, drilling into that space will be just wall material/hollow cavity/wall material. It will also be less likely to cause issues in the future. Need larger hole? Elongate with a jab saw, and use those plastic cable hiders to cover the hole.
answered Dec 31 '18 at 22:43
Edward HaynesEdward Haynes
111
Probably too late but I would actually go through the wall between the molding and the corner. Measure things on the side from the picture, transpose the hole location into the other room and drill from the other room. 3/4" auger or installer bit should fit fine. That's just me.
Drilling the frame will end up being like 5" of solid wood counting the doubled stud and the molding, drilling into that space will be just wall material/hollow cavity/wall material. It will also be less likely to cause issues in the future. Need larger hole? Elongate with a jab saw, and use those plastic cable hiders to cover the hole.
answered Dec 31 '18 at 22:43
Edward HaynesEdward Haynes
111
answered Dec 31 '18 at 22:43
Edward HaynesEdward Haynes
111
answered Dec 31 '18 at 22:43
Edward HaynesEdward Haynes
111
answered Dec 31 '18 at 22:43
Edward HaynesEdward Haynes
111
111
add a comment |
add a comment |
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f153654%2fis-it-a-bad-idea-to-drill-a-hole-through-this-door-frame-to-pass-wires%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
Dec 29 '18 at 15:28
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
Dec 29 '18 at 18:23
1
You're not going to run mains power through this, are you?
– Harper
Dec 29 '18 at 18:29